LogoSmartLife App-dokumentasjon
LogoSmartLife App-dokumentasjon
Forside
Help Center
Enhetens nettverksproblemer
Ruterkonfigurasjon
Veiledning for nettverkskonfigurering av enheter
Generelle Spørsmål om Enhetens Nettverksoppsett
Bluetooth-klargjøringsveiledning
Wi-Fi enhetsnettverkstilrettelegging
Zigbee-enhetsnettverksklargjøring
Network Provisioning for Other Protocols/Methods
Hvordan legge til enhet ved å skanne QR-koden?Hvordan bruker kameraet QR-kodeskanning for å konfigurere nettverket?Hvordan sette opp nettverk for 4G-enheter?Hvordan kontrollere Wi-Fi og Bluetooth dual-mode enheter kun via Bluetooth?Kan Wi-Fi og Bluetooth dual-mode-enheter legges til samtidig med to kommunikasjonsmetoder?Hvordan bruker enheten kabelmodus for å koble til internett?Tilkoblingsmetoder for NB-IoT-enheterHvordan Sette Opp Nettverk for NB-enheter?Hvordan få nettverksammenkoblingskoden for Matter-enheter i «Hjem»-appen
Device Connection Failure
Device Offline
Appbruksproblemer
Home, Members & Room Management
Enhetsadministrasjon og kontroll
Verdiøkende tjenester og utvidede funksjoner
Tredjepartskontrollproblemer
Veiledning for enhetsnettverksoppsett
Ofte stilte spørsmål
Brukerhåndbok
Help CenterEnhetens nettverksproblemerVeiledning for nettverkskonfigurering av enheterNetwork Provisioning for Other Protocols/Methods

Hvordan bruker kameraet QR-kodeskanning for å konfigurere nettverket?

Trinn-for-trinn veiledning for å konfigurere kameraets nettverkstilkobling ved hjelp av QR-kodeskanning.

Follow these steps to configure your camera's network connection using QR code scanning.

Configuration Steps

1. Add Device Manually

  1. Open the app home page
  2. Tap the plus sign in the upper right corner
  3. Select Add Device
  4. Choose Manual Add
  5. Navigate to Camera/Lock category
  6. Select the corresponding category

2. Reset Device to Unconfigured State

Reset the device to the unconfigured state:

  1. Connect the power supply
  2. Press and hold the reset button on the device for about 5 seconds
  3. Wait until the indicator light of the device starts to flash quickly
  4. The device enters the network configuration state
  5. Confirm the indicator light or prompt tone
  6. Click Next in the app

Common Operation: Connect the power supply, press and hold the reset button on the device for about 5 seconds, until the indicator light of the device starts to flash quickly, the device enters the network configuration state. Please refer to the instructions for details.

3. Select Wi-Fi Network

  1. Follow the prompts in the app
  2. Select the corresponding 2.4GHz Wi-Fi network
  3. Enter the password

Network Restrictions: The camera does not support public wireless networks authenticated by mobile phone verification codes or other verification methods.

4. Display and Scan QR Code

  1. Click "Next"
  2. A QR code will be displayed on the mobile phone screen
  3. Align the QR code with the camera lens
  4. Position the code about 15~20cm away from the camera
  5. Hold steady so that the camera can scan it

5. Complete Configuration

  1. After the scan is successful, you will hear a "beep" prompt sound from the camera
  2. Click "hear the prompt sound" in the app
  3. The camera will enter the network configuration process

Troubleshooting

If the camera still fails to connect successfully through the above steps, please refer to:

Device Connection Failure

What should I do when my device fails to connect to the network?

Separate Wi-Fi Bands

(For most of Routers) How to configure separate Wi-Fi SSIDs for 2.4 GHz and 5 GHz bands? Split your network into 2 frequency bands.

Innholdsfortegnelse

Configuration Steps
1. Add Device Manually
2. Reset Device to Unconfigured State
3. Select Wi-Fi Network
4. Display and Scan QR Code
5. Complete Configuration
Troubleshooting